How To Survive Your Boss On Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain and are durable and long-lasting. They don't decay or rust as aluminum or timber.

It is essential to clean and oil UPVC windows and doors regularly. This will help avoid unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and may even be fatal. It is essential to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace and typically fit into frames that were previously in use very easily. However when you have double glazed window repairs pane windows that are held in place by internal beading, it will be more difficult to remove the old panes and put in new ones. In this case, it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you are going attempt to remove the window panes by yourself it is crucial to wear appropriate safety gear such as gloves that are thick and protective eyewear. It is also a good idea to lay down a drop cloth prior to when you start working on the glass so that any shards fall onto the cloth instead of onto the floor where they could be trampled upon and cause further damage.

Once the glass has been removed, it's a good idea to seal the gap with clear packaging tape or duct tape to block water and drafts from entering the home until a professional can come out and fix the window. This also serves as a barrier to prevent any criminals from getting into your home. If the gap is particularly large, you might be interested in a security door that has an integrated window as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they are susceptible to a range of issues, including sagging. A sagging uPVC windows can cause issues with light, draughts, and even security. It is crucial to act as soon as you realize that your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window that is sliding. To do this, you'll need to open the window so that you can access the frame. With an screwdriver, unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have repositioned your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they stay in the right place.

If you cannot reposition the hinges, you may have to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to loosen. If this happens, it's essential to replace the seal as fast as possible so that your uPVC windows remain watertight and secure from draughts.

uPVC handles can also loosen up. This is typically caused by screws that have become undone over time, but it can be caused by the handle mechanism getting worn out. It's relatively simple to repair a loose uPVC handle. You'll first need to close the window and then perform an initial fitting. The corners of the sash should align with the casing joint. If it isn't, you can use the screwdriver to loosen up the handle. Then turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and mouldy walls every time it rains it's crucial to take action. The leaks of water through windows could cause structural damage to your home, and impact your ability to regulate the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant around the frame is damaged or not present.

This is an easy fix that can be done by any DIYer who is competent. Based on the severity of the problem the caulking that was used up might need to be removed before a fresh layer is applied. It is crucial to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk' as this will only make the area more difficult to clean and can reduce the efficiency of your energy.

Make sure that the drainage holes have no debris in them and ensure that the sill pan is properly angled to drain away from the window. In more extreme instances, you may need to replace the window repair.

Mold spots and rotted sills are also signs of water leakage. This fungus thrives under conditions of dampness and can spread quickly throughout the home.

If the leakage is occurring between the double-glazed window, it is more likely the problem is with the seal rather than the frame. It is also possible to be corrected by a uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or it opens in the breeze. These are easily replaced by any competent DIYer and are usually completed in a matter of minutes.

Almost every household in the UK will have either top hung or side-hung uPVC windows that have hinges and, like all mechanical parts, they can wear down over time. It's very simple to change the hinges on a window, but it's simpler if you have someone to help you to hold the frame.

It is also important to verify that the uPVC hinges are opened and closed in the correct direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

The problem can be caused due to opening the window in the wrong way or due to a poor installation at the factory. Sending us photos via our website will often solve the issue. We are more than happy to give suggestions.

It is also crucial to lubricate the hinges regularly. Applying a light engineering lubricant to the hinges is a great way to do this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window open and close more easily. It can also lower the chance of windows sticking and help prevent corrosion. Ideally, you should perform this every year. WD40 and other solvent based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. The hinges can also become misaligned due to wear, causing a gap between the frame and sash. They can be fixed by giving them a good cleaning, but when they're beyond repair, it might be necessary to get them re-aligned or replaced. The interlock may be disaligned. This is located on the hinge's side, and might require to be cleaned. In some cases it is possible to replace them.

The second most frequent reason for draughts is window seals. These are prone to wear or damaged over time, and will allow air to escape through the gaps. Replacing these with high-quality weatherstripping will help to stop draughts. Another alternative is to replace the window with low-emissivity glass. which will help regulate indoor temperatures, and also lessen the possibility of draughts.

Another, and most effective ways to reduce drafts is to use a draught excluder, these are typically made of fabric that are filled with some type of filler. They can be positioned on top of your windowsill. These will help to block out cold air and keep your home warm and cozy!

With a little regular maintenance and repairs windows made of upvc will continue to provide excellent insulation and security for your home. However, it is important to realize that all windows have a lifespan and they may reach a point where it is more economical to replace them than repair them. If you encounter any issues with your upvc window you should consult a professional immediately.