10 Kia Picanto Key Fob Replacement Tips All Experts Recommend
How to Replace a kia picanto key fob Sportage Replacement Key
The key of many Kia Venga Replacement Key models comes with an electronic keyless entry system built into. The key functions like the remote control, and can be exchanged with a Kia dealer.
Key fobs might stop working for a variety of reasons, such as an empty coin battery worn buttons or buttons, water damage, signal interference, and a defective receiver module. Here are some suggestions to help you get your 2014 kia sorento key sportage replacement key working again.
How do you replace the remote key or smartkey
No matter if your Kia comes with an intelligent key, remote key, push to start key, or a standard non-transponder key made of metal the battery in these keys will eventually need replacing. This is especially the case if your car displays a message that indicates the remote or smart keys have low battery power.
Fortunately, it's an easy process. To replace the battery of the key fob, remove the mechanical key from the slit on the back of the key fob. Next, break the cover. Inside the key fob there will be a small screw that holds the battery in its place. Take out the old battery by removing the screw using a small screwdriver. Then, you can insert the new battery and close the hole in the key fob.
When the key fob is equipped with a fresh battery Test it by pressing the lock and unlock buttons. It's okay when the doors lock or unlock as expected. You can now make use of your kia duplicate key's hands-free lock/unlock feature when your fingers start to get cold or you have to go on errands around Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key has to be programmed, you will need to know the key code number that is stamped on the tag of the key code and then record it in a safe location.
How to replace the battery
If the Kia key fob doesn't respond to pressing the lock or unlock button, it is most likely that the battery is not fully charged. A battery that is not functioning properly can cause other issues, like the check engine light flashing or the engine not running correctly. Fortunately replacing the key fob battery is a relatively simple DIY task that requires only some basic tools.
Before you begin the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Find the small metal or a plastic piece at the bottom of the key fob. Move it until the key is released. You can then put the key into the driver's door handle to open your car.
To replace the key fob's battery, take off the cover on the rear and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery and align the new battery so that the "+" positive side faces you, while the "negative" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts made of metal.
After installing the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test your Kia key fob to see whether it's functioning properly again.
How do you replace the smart key kia key
Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs contain a battery inside them that will eventually need to be replaced. This is an easy process that takes less than two minutes.
Before you get started before you begin, ensure that you're on a level surface with enough lighting and that your Kia is off. Be aware that the fob has small parts that can be thrown off should you not be careful.
The first step is to find the small release button that is located on the lower backside of your fob. This will either be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.
Once you have the key fob opened and you are able to take off the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you've finished, you should be able to lock, unlock and start your car with your key fob, even if your engine isn't running!
How do you replace the mechanical key?
The Kia keyfob is an excellent convenience which allows us to lock or unlock our car with just pressing the button. However, like all devices there are issues with it occasionally. Luckily, there are steps that can be taken to fix these issues and ensure that our key fobs are in good working condition over the long haul.
A dead or low-quality battery is among the most frequent problems. This can cause the device to stop working altogether or work intermittently. If this happens, try replacing the battery with a new one.
If this isn't enough to resolve the problem you can try using a standard flathead screwdriver to open the casing of the fob's plastic. Be sure not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the old battery and replace it with a new one.
Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and verify that it's working correctly. Contact a dealer or a locksmith to solve the issue when the fob still is not working. To avoid future lockouts, ensure you have an emergency key that can work on all trunk and door cylinders.